When the machine is stopped for a long time, we should pay attention to some details, Maple Machinery would like to inform all of our customers to pay attention to the instruction and placement of machine shutdown. 1. Shutdown 1.1 Maple Machine Centers Cleaning Procedures: Clean up the work piece, fixtures, metal chips and so on. Clean the metal chips in the external chip removal machine; Wipe out the external sheet metal, and clean the electric box air conditioner and the filter of oil cooler first. 1.2 Anti-rust Treatment: A. Wipe down the work table and smear the anti-rust oil; B. Spindle taper hole: use the cloth with lubricating oil to wipe the spindle taper hole; C. Run the machine at a slow speed and lubricates the rails; D. If the cutting fluid needs to be replaced, give priority to anti-rust treatment. The machine tool needs to add cutting fluid at the beginning. 1.3 Shutdown and power off: Run the X and Y axes to the middle, the Z axis return to origin, and turn off the main electrical switch of the machine tool, the incoming switch of the transformer, the air source, etc. 1.4 Keep away from rain and moisture: Close the electrical box for protection. 1.5 Rat proof processing: The machine tool is well protected against rodents to prevent rats from biting off the wires. 2.Starting up 2.1 Check before starting up: Check the surrounding environment of the machine tool, whether there is any abnormal phenomenon such as water or liquid in the electrical box, whether the oil has deteriorated, and whether the oil such as the tool cylinder, rail lubricator, oil cooler is sufficient. 2.2 Gradually starting up: The external main switch is powered on first, check whether the voltage is out of phase and too low, turn on the power of the machine tool under abnormal conditions, and observe whether there is any abnormal phenomenon or air leakage. 2.3 Starting up observation: Under the condition of no alarm when starting up, do not perform any action and let the electrical components be energized for 30 minutes. 2.4 Slow moving: Check for interference, move the machine tool with the hand wheel all the way, pay attention to any abnormalities, and then perform the origin return step. 2.5 Machine running: Run the machine slowly at a slow speed for a long time, and rotate the spindle at a low speed. 3.Placement conditions 3.1 Maple CNC Vertical Machine Centers should be placed in a constant temperature environment, and the working environment temperature should be between 0~35°C. Avoid direct sunlight on the CNC vertical machine center, and avoid the influence of humidity and airflow. Generally speaking, an exhaust fan is installed inside the electric control box to keep the electronic components, especially the central processor's working temperature is constant or the temperature difference changes little. Extremely low temperature or instability will reduce the life of control system components and lead to increased failures. At the same time, the room should be equipped with good lighting equipment. 3.2 In order to improve the accuracy of machining parts on the Maple machine centers and reduce the deformation of the machine centers, if necessary, the CNC machine tool can be installed in a relatively closed workshop equipped with air-conditioning equipment. 3.3 The relative humidity of the working environment should be less than 75%. When the humidity increase in dust will cause adhesion on the integrated circuit board and cause short circuits. Therefore, pay extra attention to the environment in rain and snow, and keep it as dry as possible. You can also add a dust cover on the machine to prevent dust. 3.4 Maple CNC Machine Centers should be installed in a place away from liquid splashes and prevent leakage of water from the workshop. Keep away from the environment with excessive dust and corrosive gas, and away from equipment with strong vibration (such as punch) and equipment with electromagnetic interference. Everyone remember to do a good job of machine shutdown and placement before the holidays so we all have a smooth start after lockdown. 

? Thank You, Netherlands! A heartfelt thank you to our Dutch friends for the warm and generous reception! We had an inspiring and productive meeting discussing Maple's latest product innovations and strategic roadmap, while exchanging insights on global trends in automation and AI technologies. ? Exciting ideas were shared. New possibilities were sparked.We truly look forward to what the future holds—and to the innovations we'll create together. Let’s make it happen! ? #MapleTechnology #Automation #AI #SmartManufacturing #Innovation #GlobalPartners

Start changing and reducing plastic usement from now on

  MAPLE Achieves Latest CE Certification for Machining Centers & Lathes   We’re proud to announce that MAPLE TECHNOLOGY has officially obtained the latest CE certifications for both our CNC machining centers and CNC lathes—a testament to our commitment to international quality and safety standards. ?️ Lathes: After 3 months of rigorous inspection and documentation review, our CNC lathe series has successfully passed the SGS appraisal and met the CE requirements.?️ Machining Centers: We have updated our compliance from EN ISO 16090-1:2018 to the latest EN ISO 16090-1:2022 standard. At MAPLE, we truly care about everything related to machines.We deliver reliable technology so you can focus on growth—with confidence. ? Trust MAPLE for your next win-win collaboration. ? Contact Us? Website: www.maple-tech.com.tw? Email: info@maple-tech.com.tw? Instagram: @mapletech? LinkedIn: Maple Technology

With our boss, Chuan Lin's leading, Maple team have been in Cebu, Philippines from DEC 13 to 17 and had good memories there. Thanks our boss treating us so kindly. Through these five days, we had knew more about each other. Maple have received full positive energy and back to work hard with you all

?? Maple Technology Expands to the Czech Republic We are proud and delighted to announce the official launch of Maple Technology Co., Ltd. machines in the Czech Republic! Your warm hospitality and genuine friendship made our journey truly unforgettable.Thank you for making our stay so special—we deeply appreciate your support and trust in Maple. ? We look forward to building a strong and lasting partnership with you. See you again soon!

Stronger, Stronger, Better......

We're capturing the great pictures of our new beautiful lathe series today since they have been sold to America, Europe, Southeast Asia, and so on. Because Maple truly believes that we will not only impress customers but subvert their imagination. #Endless #Innovation #Maple #CNC #machine #center #Taiwan #company #customed #profession #protection #machine #tools